吸盘/聚氨酯
聚氨酯波纹管吸盘 VG.BP52
• 适用于zui低水平补偿,稳定性高
• 对瓦楞或多孔表面或非密封表面(例如纸板、塑料制品和不规则表面的复合材料)具有极i好的抓持力
• 也适用于提升力与表面平行的应用
• 具有非凡的弹性记忆功能
• 可提供 50 肖氏硬度,绿色
• 可提供 30/70 肖氏硬度。同时双色吸盘既坚固又灵活
材料聚氨酯 PU
颜色 黄色 / 绿色
硬度 30/70
温度范围+10 - +45 °C
吸盘/符合 FDA 标准的硅氧烷
VG.FO33F 扁平吸盘,采用符合 FDA 标准的硅氧烷材质制造,带有加强件和薄唇口
• 适用于打开袋子和处理薄而精致的物品,例如板和薄膜
• 内部纹理和薄唇口可防止损坏处理的物品,同时保持其平整度
• 吸盘由 FDA 批准的透明硅氧烷制成
技术数据
材料SIL 50 FDA
在不同真空度下与表面垂直的提升力 [N]-20 kPa -60 kPa -90 kPa 16.2 38.3 49.2
在不同真空度下与表面平行的提升力 [N]-20 kPa -60 kPa -90 kPa 13 30 39
体积 2.1 [cm³]
zui小曲线半径 35
zui大垂直移动距离1.5
吸盘质量5
自动校准中心气动针状夹具 PT
• 4根(PT25)或者8根(PT28)直径2mm的针。
• 适合塑料、纺织或食品工业。
• 双动作。
• 瞬时调整针行程 (1)。
• 多个安装附件 (2)。
• PT25: 大通孔 (3)。
• PT28: 用于清洁和释放的排放口 (T)。
• PT28: 用于接触热表面的PTFE 垫 (4) 。
• PT28: 选装磁性传感器 (5)。
Self-centering pneumatic needle gripper series PT
• 4 needles (PT25) or 8 needles (PT28) with 2mm diameter.
• Suitable for p1astics, textile and food industry.
• Double acting.
• Needle simultaneous stroke adjustment (1).
• Several mounting accessories (2).
• PT25: Large through hole (3).
• PT28: Blow-off port (T) for cleaning and releasing.
• PT28: Pad in PTFE (4) for hot surface contact.
• PT28: Optional magnetic sensors (5).
编程单个SB8F
在对传感器盒进行编程之前,请确保有线输入处于所需配置(开/关)以启用输出。按下AUTOSET按钮并按住3秒钟,直到READING红灯开始闪烁,然后松开。红灯(READING)闪烁表示微处理器正在读取和存储全部输入的状态。然后红灯熄灭,启用了输出。黄灯(STORED)指示启用输出。
Before programming the sensor box, make sure that the wired inputs are in the confguration (ON/OFF) desired to enable the output. Press the AUTOSET button and hold it down for 3 seconds until the READING red light starts fashing, then release it.The red light (READING) fashing indicates that the microprocessor is reading and storing the state of all the inputs. Then the red light goes off and the output is enabled. Output enabling is indicated by the yellow light (STORED).
以上信息由专业从事机器人抓持器的吉玛泰克于2024/4/18 13:13:40发布
转载请注明来源:http://xinxiang.mf1288.com/jmtkzdh-2737674915.html